







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Kohler Bathroom Remodeling in Irving: What to Know First
Kohler bathroom remodeling in Irving typically runs $9,000 to $28,000 for a full gut remodel, and most Kohler jobs we handle – a new shower valve behind the wall, a vanity swap, a tub-to-shower conversion – take three to five weeks from tear-out to final inspection. We’re an independent Kohler service provider, which means we install Kohler fixtures and tile to the same standard Kohler builds their products to. If you’re in Las Colinas with a 1990s Memoirs bath you’re finally ready to gut, or in Valley Ranch with a shower cartridge that’s been weeping for a year, this page is written for you. Call (833) 991-4970 for a free estimate. We show up, we quote, and the quote doesn’t change unless it changes in writing.
How Kohler Products Fail – and How We Fix Them
Kohler builds a good fixture. But “good fixture” and “no failure” aren’t the same sentence. Here’s what we actually find in Irving bathrooms, and why.
- Cartridge corrosion in Kohler shower valves (Rite-Temp, 2-handle models from the 1990s). Irving’s water runs hard – Trinity River supply, plus the limestone-heavy well water once you’re out toward Hackberry or the unincorporated pockets near Belt Line. Hard water eats through the ceramic disc and brass cartridge in roughly 8 to 12 years. The symptom owners notice first isn’t a drip. It’s a shower that gets hot slower, or runs lukewarm on the left and scalding on the right. That’s a cartridge, not a valve body. We pull the cartridge, scope the body, and swap the cartridge for OEM whenever the body’s still true. A rebuilt valve costs a fraction of a full valve replacement behind tile.
- Memoirs under-counter bath sink caulk failure at the backsplash. The Memoirs pedestal and undermount product line has a low rail profile against the baseboard – beautiful, but the caulk joint behind that rim fails in 4 to 6 years in Irving’s swing from humid summer to dry winter. Water tracks down and rots the cabinet toe kick, not the sink. We rebuild the joint with a silicone-based sealant rated for the expansion, not a latex tube.
- Iron/steel bath tubs losing enamel at the overflow. Kohler’s cast iron tubs (Villager, Bellwether) hold up for decades but the enamel starves right under the overflow plate. That’s the drip you can’t find. We refinish rather than replace when the tub’s still solid, and we open the overflow to inspect the shoe gasket before we quote.
- Faucet aerators and hand-shower screens clogging with mineral scale. Kohler’s Purist and Loure products have a fine mesh screen behind the aerator that clogs on Irving water within 18 to 24 months. The flow drops and owners think the faucet’s dead. It’s not. We pull, descale, and re-seat. If the aerator body itself is pitted, we replace it OEM.
- Toilet fill valves (Kohler Wellworth, Cimarron) cycling short. The fill valve on Kohler’s 1.28 GPF models is a known wear point after 6 to 8 years. Short cycling on the fill isn’t a flapper problem; it’s the float cup. We replace the fill valve as a unit when it’s gone, not just the flapper, so you’re not back in six months.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Our Kohler Bathroom Remodeling Process
- 1
Walk-through and diagnostic. We pull the aerator, check the valve cartridges, inspect the tub overflow shoe, and get eyes on the subfloor. On Kohler jobs, this matters more than on cabinet installs because the answer is usually behind the wall.
- 2
Parts decision, in writing. OEM versus quality aftermarket gets decided out loud, on paper, with the Kohler part number on the change order. We don’t use the cheapest aftermarket cartridge and call it Kohler. We use Kohler OEM where it matters (cartridges, fill valves, drain shoes), and quality aftermarket where the OEM premium buys nothing (caulk, escutcheons on cosmetic replacement).
- 3
Permits pulled. Every eligible Irving job gets a permit. Plumbing rough-in, electrical if we’re moving the vanity outlet, and final inspection. The permit inspector works for you, not for us – that’s why we like him.
- 4
The build. Demo, rough-in, tile backer, tile, fixture set. Our crew members cap the water, protect the floor, and keep the rest of the house livable. Up to 28 years of experience across the bathroom side of the business, and the sons run the job, not a stranger.
- 5
Test, hold, and walk-through. Every valve gets a 10-minute flow test at temperature. Every drain gets a bucket test. Every caulk joint gets the eye.
- 6
90-Day Done Right Promise. Written on the contract. If something’s off, one call brings us back inside 90 days. That’s the whole promise.
See the difference
Before
After
Before
After
Before
AfterWhat Kohler Bathroom Remodeling Costs in Irving
| Scope | Typical Range |
|---|---|
| Full bathroom remodel (tub, shower, vanity, tile, Kohler fixtures) | $9,000 – $28,000 |
| Small bathroom remodel (powder room or half bath) | $5,000 – $12,000 |
| Kohler walk-in shower installation | $4,500 – $12,000 |
| Tub-to-shower conversion (Kohler shower base and valve) | $3,500 – $10,000 |
| Shower replacement (base, tile, valve, trim) | $3,000 – $8,500 |
| Kohler vanity installation (cabinet and top) | $800 – $3,000 |
Kohler fixture pricing pushes the low end up by $400 to $1,200 versus a builder-grade brand for the same footprint – a Kohler Rite-Temp valve and trim set runs more than a contractor special, and Kohler ceramic tile trims run higher than stock. What moves the number most: whether the valve body has to come out (a full-body valve on a 1990s Kohler install can add $600 to $1,400), whether the subfloor is sound (Irving slab-on-grade, always a check), and whether you’re keeping the tub or converting to a shower. Free estimates, line-item written. Call (833) 991-4970 for an exact quote on your Irving bathroom.
Why Irving Homeowners Call Barrett & Sons Construction Irving for Kohler Work
We’re not the biggest name in Irving, and we’re not a national outfit quoting one price on the phone and handing you another at the door. We’re the owner-operated alternative – Tom Barrett and his sons on the job, up to 28 years of technician experience on bathroom work, and a written 90-Day Done Right Promise on every contract. A live person answers the phone, 24 hours a day, seven days a week. We pull the permit, we get the inspection signed, and every price change is a written change order before a single Kohler cartridge gets swapped. We also install KraftMaid, GAF, PGT, and Master Halco on the rest of the house, so you’re not chasing a different crew for the roof when the bathroom’s done. Look us up before you sign anything – the name, address and license number are public. Ask anyone on your street.
FAQs

Not if it’s done right. Kohler’s limited warranty covers defects in material and workmanship and it doesn’t care who installed the fixture – it cares whether the fixture was installed per Kohler’s published instructions. What voids coverage is installing a Kohler valve with a non-Kohler cartridge, using an aftermarket trim that doesn’t fit the valve body, or roughing in at the wrong depth. We install to spec, we keep the install paperwork, and we hand you the Kohler warranty documentation at the walk-through. Call (833) 991-4970 with the model number off your fixture and we’ll tell you what we’re working with.
Usually yes, and the reason is simple: Kohler keeps replacement cartridges and trim kits in production for most of their historic series far longer than the box stores do. The Rite-Temp valve cartridge for most 1990s installs is still available OEM. What gets harder is discontinued trim finishes (the old Vibrant Brushed Nickel shades, for instance) – those we source from Kohler’s parts channel or from a quality aftermarket that matches close. If the part is gone, we tell you straight and quote the closest available replacement in writing before we start.
Repair, unless the tile and valve body have both failed. A weeping Rite-Temp cartridge in a shower with intact tile and a true valve body is a $200 to $600 repair, not a remodel. What pushes toward replacement: a valve body that won’t hold a cartridge (happens on 1990s installs in Irving hard water), tile that’s tenting behind the shower valve, or a tub you’re already planning to convert. We’ll quote both ways, in writing, so you can see the numbers side by side. Call (833) 991-4970 and we’ll get a walk-through scheduled.
Three to five weeks for a full bath, ten days to two weeks for a tub-to-shower conversion with Kohler base and valve, and often one to three days for a cartridge or vanity swap. The clock starts when the permit is pulled, not when we quote – Irving’s permitting office turnaround is usually a few business days, and we account for it in the schedule we give you. No surprise finish dates. Call (833) 991-4970 for an exact timeline on your job.
Yes. Every eligible job gets a permit pulled and an inspection signed. We’ve heard too many stories about the last contractor who told a homeowner permits were optional – they aren’t, and the inspection is the homeowner’s protection, not ours. You get the signed inspection paperwork at the end. Call (833) 991-4970 for a free estimate and we’ll walk you through what your job requires.
Written by the team at Barrett & Sons Construction Irving, serving Irving and nearby areas.












