Last updated November 18, 2026








Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
DIY vs Professional Fence Installation: What’s Safe to Do Yourself
The most common DIY fence failure we see in North Texas has nothing to do with the boards, the panels, or the gate hardware. It’s the posts. Specifically, posts set at the standard two-foot depth that works fine across most of the country but fails in soil that swells and contracts by several inches over a single season. A homeowner in Irving can build a genuinely straight, solid fence and still watch it lean within eighteen months because of one number on a post-hole digger. This guide is about where the real line sits between what you can safely handle and what will cost you more in the long run. We’ll cover the clay-soil depth formula, the tasks that are truly low-risk, the equipment you’ll actually need and rent, permit rules, and how a partial-hire arrangement works.
Quick Answer
Staining, painting, replacing individual boards on stable posts, and swapping a gate latch are safe DIY projects for most homeowners. Full fence installation in Irving is a different animal: the post depth and concrete mix required for Blackland clay are the two steps that decide whether the fence lasts ten years or leans in two, and both are easy to get wrong without experience. Permits are required either way – DIY or professional – so the paperwork burden doesn’t disappear when you do the work yourself.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Table of Contents
- The Post Depth Problem in Irving’s Clay Soil
- What’s Genuinely Safe to Do Yourself
- The Equipment a Full DIY Install Actually Requires
- Permits: They’re the Same Whether You DIY or Hire
- How a Partial-Hire Arrangement Works
- Material Choices That Affect the DIY Decision
- How Long a Full Install Really Takes
- What Each Approach Costs in Irving
The Post Depth Problem in Irving’s Clay Soil
The generic advice you’ll find on most fencing sites is “bury a third of the post height.” For an eight-foot post, that’s roughly thirty-two inches. It sounds reasonable. It is also the single reason we get called to reset more leaning fences in Irving than anywhere else we work. Blackland clay – the dark, heavy soil that covers much of Irving and the surrounding county – expands when it’s wet and shrinks when it dries. That movement is measured in inches, not fractions of an inch. A post set to the generic depth in ordinary soil holds fine. A post set to the generic depth in this clay gets worked loose, season by season, until the whole run is out of plumb.
The adjusted formula for Irving’s soil runs deeper. For a six-foot fence, plan on a minimum of thirty-six inches of post below grade, and forty-two inches is better for gate posts and corner posts that carry more lateral load. For an eight-foot privacy fence, we don’t set anything shallower than forty-eight inches. The deeper setting gets the base of the post below the active zone – the layer of clay that actually moves with moisture. That’s the point most DIY guides miss: it’s not the depth number alone that matters, it’s getting past the soil that shifts.
Here’s how you verify you’ve actually hit it, because a tape measure on the side of the hole lies to you when the hole is wider at the bottom:
- Mark your target depth on a straight scrap board or a length of rebar with tape before you start digging.
- Set the marked stick in the hole and check it from two sides at right angles – a hole that’s bell-shaped at the bottom can read deep on one side and shallow on the other.
- Confirm the bottom of the hole is undisturbed soil, not loose backfill. If the bottom is soft and crumbly, dig another four inches and recheck.
- For gate posts, add six inches beyond your target as a margin, because that post takes the most stress.
Concrete mix matters just as much. A dry pour-and-water mix works in sandy soil. In clay, we use a bagged mix at the correct ratio so the concrete cures consistently around the post rather than leaving voids where water pools. If you’re planning a fence and want the full scope of what professional installation involves in this area, our Fence Installation in Irving page walks through the process from layout to final inspection. And if your fence project is part of a larger backyard plan that includes a patio or new driveway, our Driveway & Pavers in Irving guide covers how hardscape and fencing schedules should line up.
What’s Genuinely Safe to Do Yourself
Here’s the part most contractors won’t tell you: a lot of fence maintenance is absolutely a weekend project, and nobody needs to pay us for it. We’d rather tell you honestly what to try yourself so the conversation is focused on the work that actually needs a crew. The tasks below carry low risk of injury and low risk of structural consequence. None of them require special licenses in Irving, and all of them can be done with tools most homeowners already own or can borrow.
- Staining or sealing an existing fence. This is the highest-return DIY task on the list. North Texas sun is brutal on wood, and a fresh coat every few years adds years to a fence. The only trick is waiting for a stretch of dry weather and applying when the wood isn’t hot to the touch.
- Replacing individual pickets or boards on stable posts. A board cracks or warps, you swap it. If the posts underneath are plumb and solid, there’s no structural risk. This is a screwdriver-and-hammer job.
- Swapping a gate latch or hinge. A sagging gate is often just worn hardware. Replacing a latch or hinge is straightforward, and if the gate sags because the post has moved, that’s the point where you call someone.
- Painting a fence that’s already sound. Paint and stain follow the same logic. Prep and apply. No excavation, no concrete.
- Tightening loose fasteners. Rattle a fence panel and check the screws. A pass with a driver once a year catches small problems before they’re big ones.
Notice what’s not on that list: anything that involves digging, setting posts, or building from scratch. Those are where the structural decisions live, and those decisions are the whole ballgame. We’ve pulled boards off fences in Irving that looked perfectly fine on the surface and found posts barely four inches into the ground – hidden until the first big rain.
The Equipment a Full DIY Install Actually Requires
The first time most homeowners price out a full DIY fence installation, they forget the equipment. It’s not just a shovel and a level. Blackland clay is hard as concrete when it’s dry, and the ordinary hand-powered post-hole digger you’d borrow from a neighbor will bind up within a few inches. Here’s what a real install in Irving requires:
- A powered auger (one- or two-man). Rental in the Irving area typically runs $75-$125 for a day, more for a two-stage model that handles clay.
- A rotary hammer or heavy breaker bar for the hardest dry clay, roughly $50-$90 a day to rent.
- Post hole digger (manual) and a digging bar for cleanup and finish work, about $20-$40 to buy or borrow.
- A post level and a long spirit level. Two levels make plumbing a post much faster. Around $30-$60 to buy.
- String line and stakes for layout. Inexpensive but essential.
- A wheelbarrow and mixing tub for concrete. Around $60-$100 to buy if you don’t own them.
- A circular saw or miter saw for cutting panels and rails. Most homeowners own one already.
- Safety gear: gloves, safety glasses, and a back brace if you’re not used to this kind of lifting.
Add it up and the equipment side alone runs $250-$400 for a one-time install, plus the time to rent, load, and return everything. That’s before concrete, lumber, and hardware. It’s not a reason to hire a contractor by itself, but it’s part of the honest math. If your broader outdoor project includes pavers or a new drive, our Barrett & Sons Construction Irving home page lists the trades we handle and how they connect.
Permits: They’re the Same Whether You DIY or Hire
This is the point where a lot of DIY installations quietly go off the rails. The permit requirement in Irving doesn’t change based on who’s holding the shovel. A fence over a certain height, or one that replaces an existing fence, or one on a corner lot, has permit requirements regardless of whether you build it or a crew builds it. The city doesn’t care who built it – it cares that it was built to code and inspected. Fence height limits, setback requirements in certain zones, and rules around corner lots with sightlines are all governed the same way.
Here’s what happens when an unpermitted fence is discovered, and we’ve seen this play out more than once. During a home sale, a title search or the buyer’s inspection can flag a fence that has no permit on file. The seller then has to either get a retroactive permit – which means an inspector showing up to look at a fence that may not meet current code – or tear it down and rebuild. Either outcome is expensive and slow, and it can delay a closing. The permit inspector works for you, not for us. That signature on the inspection card is proof the fence was built to the rules, and it belongs to the homeowner whether the labor was hired or DIY.
What you’ll need on the permit side, in plain terms:
- Check with the city for the current fence height and setback rules that apply to your specific lot.
- Submit the permit application with a site plan showing the fence location and height.
- Schedule the inspection after the fence is built and posts are set.
- Keep the inspection record with your home paperwork – it matters at resale.
If your project involves a fence plus another structure like a detached garage or an addition, the permitting gets more involved. Our Home Additions & ADU in Irving page explains how multi-structure permits work when you’re adding to the property.
How a Partial-Hire Arrangement Works
This is the option most homeowners don’t know to ask about, and it’s the smartest way to get the benefit of both approaches. The posts and footings are the hard, structural, inspection-sensitive part of a fence. The panels and pickets are the time-consuming but straightforward part. A partial-hire arrangement splits the job on that line: a crew sets the posts, footings, and gate posts to the correct depth and concrete mix for Irving clay, and the homeowner installs the panels and pickets afterward.
What does that save? On a typical residential fence in Irving, the posts and footings represent a smaller share of the labor than the panels, but they’re the share that’s hardest to get right. Doing the panels yourself after the crew leaves saves meaningful labor cost while keeping the foundation of the fence in professional hands. It also means the inspection-critical part is done correctly and documented. The conversations to have with a contractor before splitting the work:
- Who is pulling the permit, and in whose name.
- What scope the crew is responsible for, in writing – posts only, posts plus rails, or posts plus frame.
- What happens if the homeowner’s panel install doesn’t pass inspection, and whether the contractor will return to correct it.
- How the work is scheduled so posts cure before panels go on.
- What materials the homeowner supplies versus what the contractor supplies.
The single biggest mistake in a partial-hire is skipping the written scope. Get it in writing – what the crew does, what you do, what the price is, and what happens if a step gets adjusted. If any price change shows up, it should arrive as a written change order before the work happens, not as a surprise on the invoice. That’s the standard on every job we run.
Material Choices That Affect the DIY Decision
Some fence materials are more forgiving of DIY installation than others. Wood and vinyl are the two most common choices in Irving, and they’re not equal when it comes to homeowner-friendly installation.
Wood is easier to cut and correct on the fly. If a post is slightly out of plumb or a panel needs to be trimmed, wood forgives the mistake. Vinyl is less forgiving because the panels are factory-cut and the tolerances are tighter – a gap in post spacing shows up as a misaligned panel that can’t be sanded back into shape. We install premium vinyl brands like Bufftech and ActiveYards because the panels come with predictable dimensions and matching hardware, but those same reliable dimensions punish rough layout. If you’re going to attempt a vinyl install on your own, plan on being precise with post layout to within a fraction of an inch.
Ornamental aluminum and steel follow the same rule – forgiving on installation, expensive to correct. Chain link is the most DIY-friendly of the metal options because the structure is more forgiving of slight variation. And whatever material you choose, the footer work is the same: set to the adjusted depth, mixed correctly, and cured before the panels go on. Materials don’t change the post depth requirement in this clay.
How Long a Full Install Really Takes
One of the honest things contractors don’t always say is how long a fence installation genuinely takes when it’s done right, because the answer exposes the lie in a lot of DIY video timelines. A crew of two or three people with proper equipment can set and cure posts, then build out a standard residential fence run in a couple of days. A first-time DIY homeowner with a borrowed auger, a wheelbarrow, and weekends is looking at a much longer project – often three to five weekends for a typical backyard, longer if the ground is dry and the clay fights back.
Add the concrete cure time and the inspection wait, and the DIY timeline stretches further. Posts need time to cure before panels are loaded onto them, and an inspection can’t happen until the fence is built. It’s not a one-weekend job. It’s a season-long one for most people. That’s not a reason to avoid it – it’s a reason to plan for it honestly.
What Each Approach Costs in Irving
Local pricing varies by material, linear feet, and site conditions, but here’s a realistic working range for a typical residential fence in the Irving area. These are ranges, not quotes – the only way to know your actual number is a written estimate from a contractor who’s walked the property.
| Approach | Typical Cost Range (per linear foot) | What’s Included |
|---|---|---|
| Full DIY (all phases) | $20-$35 | Materials, rental equipment, permit, your labor |
| Partial hire (posts + footings professional) | $32-$50 | Materials split, equipment, permit, crew labor for posts, your labor for panels |
| Full professional install | $45-$75 | Materials, labor, permit, inspection, warranty |
Whatever route you choose, ask for a written, line-item quote – not a single number on the phone. Every scope detail, every allowance, and every change order should be in writing before work begins. That’s what we do on every job, and it’s what you should expect from any contractor you hire.
Common Mistakes to Avoid
- Setting posts at the generic one-third depth. The rule doesn’t account for Irving’s Blackland clay, and posts set that shallowly loosen within a few seasons.
- Skipping the concrete mix ratio check. A dry pour-and-go bag works in sandy soil, but in clay it leaves voids where water pools and rots the post base.
- Building without a permit because “it’s just a fence.” Irving requires permits for many fence projects, and an unpermitted fence can derail a home sale years later.
- Loading panels before posts cure. It’s tempting to save time, but posts that are loaded early can shift out of plumb before the concrete has fully set.
- Renting the wrong auger for clay soil. A standard one-man auger binds in dry Blackland clay. Rent the heavier model or expect to fight the ground.
- Undershooting post count to save money. Wider post spacing is one of the most common causes of sagging panels in North Texas heat.
- Splitting work with a contractor without a written scope. Without it, disputes over who does what – and who pays for corrections – become very costly very fast.
See the difference
Before
After
Before
After
Before
AfterWhen to Call a Professional
Call a professional if any of the following is true: the fence requires a permit and you’re not comfortable with the inspection process; the ground is dry Blackland clay and you don’t have the right auger; the run is longer than a small backyard section; you need gate posts that carry heavy loads; or the fence is part of a larger project that needs to coordinate with other trades. Those are the situations where doing it yourself costs more than it saves. Barrett & Sons Construction Irving offers free estimates in Irving – call (833) 991-4970 and we’ll walk your property, tell you honestly what’s worth doing yourself, and what’s better left to a crew. Our technicians have up to 28 years of experience, every eligible job gets permits pulled and inspections signed, and every price change comes as a written change order before it hits the job.
Frequently Asked Questions

Often, yes – Irving requires permits for many residential fence projects, particularly those over a certain height or on corner lots. The requirement is the same whether you install the fence yourself or hire a contractor. Before you dig, call the city to confirm what applies to your lot, and if you hire, confirm in writing that the contractor is pulling the permit in your name.
Deeper than the generic one-third rule. For a six-foot fence in Irving’s Blackland clay, plan on a minimum of thirty-six inches below grade, and forty-two inches for gate and corner posts. For an eight-foot fence, we set nothing shallower than forty-eight inches. The goal is to get below the active clay layer that swells and shrinks with moisture, because that’s the movement that makes posts lean.
Full DIY is usually cheaper on paper when you don’t count your own labor, but the savings shrink fast once you add equipment rental, the permit, and the risk of a do-over if the posts fail. Partial hire – professional posts and footings, DIY panels – often lands in the middle and keeps the structural part done right. Call (833) 991-4970 for a free estimate and we’ll price both approaches side by side.
Not without your signature. On every job we run, any change to scope or price arrives as a written change order before the work happens. If a contractor quotes you a phone price and shows up with a different number at the door, that’s the exact situation the written change order is designed to prevent.
It can delay or complicate the sale. A title search or buyer inspection may flag a fence with no permit on file, and the seller then has to either obtain a retroactive permit – which requires an inspection – or rebuild. Get the permit and the signed inspection at the time of installation, whether you DIY or hire, and keep the record with your home paperwork. It’s the cheapest insurance you’ll ever buy on a fence.
Frequently, yes. A partial-hire arrangement on posts and footings is one of the smartest ways to save on a fence project while keeping the structural work professional. Have the conversation explicitly, put the scope in writing, and confirm who is pulling the permit and in whose name. That one page of paper is what keeps a split project from turning into a dispute.
The Bottom Line
The line between DIY-appropriate and professional-only on a fence project runs almost entirely through the posts. Painting, staining, swapping boards on solid posts, and replacing gate hardware are yours to handle. Post depth and concrete mix for Irving’s Blackland clay are not – those two decisions determine whether a fence stands ten years or leans in two, and the permit and inspection apply either way. If you want the honest split, a partial-hire arrangement gets you the best of both: professional posts and footings, your labor on the panels. Always ask for line-item written quotes, written change orders on any scope change, and proof the permit is pulled in your name. That’s the standard we hold ourselves to on every fence in Irving.
Barrett & Sons Construction Irving is a local, owner-operated company – founded in 1998, with a name on every job and a 90-Day Done Right Promise written on every construction contract. Every eligible job gets permits pulled and inspections signed, every scope and price change arrives as a written change order before a nail moves, and premium brands across every trade mean the materials you’re quoted are materials you can look up. We answer the phone with a live person, not a voicemail box. For a free estimate, call (833) 991-4970.
Written by the team at Barrett & Sons Construction Irving.


